Where does the
water reach?
A wave arriving at a beach or sloping defence does not stop at the still-water shoreline. Water moves up the slope and returns downslope. A high crest may be reached only occasionally; a lower crest may allow repeated overtopping. Elevation, exceedance probability and discharge describe different parts of this behaviour.
Separate the water levels.
Still water level is the reference level for the calculation, including the selected tide and surge contribution. Wave setup is a wave-induced change in the mean level. Swash is the fluctuating shoreline motion about that mean. Run-up describes the elevation reached relative to a stated reference, so the reference and any setup contribution must be made explicit.
For an idealized beach, instantaneous shoreline elevation may be written z(t) = zSWL + setup + swash(t). That accounting identity is not a run-up predictor. The structural formula below predicts Ru2% relative to its specified SWL; do not add a separate setup estimate to its output without checking the formulation and reference level.
A high percentile is not a maximum.
Ru2% is the run-up height exceeded by 2% of incoming waves under the specified sea state. It is neither the largest possible run-up nor a 2% annual flood probability. Crest freeboard Rc = zcrest − zSWL measures the height available above the still water level.
Mean overtopping discharge q is the volume crossing the crest per unit time and per metre of structure length. It has units m³/s/m, equivalently m²/s; multiplying by 1,000 gives L/s/m. A small average can conceal intermittent large events. Ru2% below the crest does not imply zero overtopping, and q is not a flow velocity.
Raise the water. Keep the crest fixed.
This calculator uses EurOtop (2018) mean-value relationships for a straight, smooth, impermeable slope under normal wave attack. All influence factors equal one. Inputs Hm0 and Tm−1,0 are the incident sea-state parameters at the structure toe, not untransformed offshore values or a peak period.
Blue: SWL. Coral: Ru2% elevation on a hypothetical continued slope. Navy: crest. Heights are relative to one local datum; geometry is schematic.
Blue: predicted mean q while varying Rc alone. Coral dot: current freeboard. Vertical scale is logarithmic; small values are not zero.
Toe bed is fixed at −10 m datum, so toe depth = 10 + SWL. Changing SWL here holds the entered toe wave conditions fixed. A real tide or surge can also change wave transformation before the toe.
Try three comparisons.
- Raise SWL without moving the crest. Freeboard falls. Compare the corresponding increase in overtopping.
- Increase the crest elevation. Ru2% remains unchanged in this formulation, while q decreases. Run-up on an uninterrupted slope and discharge across a finite crest answer different questions.
- Change the energy period while keeping Hm0 fixed. The surf-similarity parameter changes. Try an input outside the teaching range and read why the quantitative prediction is withheld.
From a rate to a volume.
A hypothetical mean q = 0.010 m³/s/m equals 10 L/s/m. If that rate were uniform along a 20 m crest and steady for ten minutes, the total overtopped volume would be 0.010 × 20 × 600 = 120 m³. It does not tell us the peak volume of one overtopping wave or the depth of flooding behind the structure.
Equations, units and the selected branches
Write H = Hm0, T = Tm−1,0 = m−1/m0, tanα = 1/n and g = 9.81 m/s². The reference deep-water wavelength L0 = gT²/(2π) is used to define the surf-similarity parameter even though the wave parameters are specified at the toe; it is not a claim that the toe is in deep water.
These are EurOtop (2018) Eqs. 5.1–5.2 and 5.10–5.11 specialized to all influence factors equal to one. “With a maximum of” is implemented as the smaller of the two branch values, not their sum. The fractional power applies to the full positive quantity inside its parentheses; the minus sign stays outside that power. The chart and numerical results use the same function.
The run-up equations give a mean prediction of the 2% exceedance level; the overtopping equations give a mean prediction of the time-averaged discharge. Neither is a conservative design assessment. Empirical scatter and uncertainty in wave conditions, water levels and geometry remain. The displayed digits support comparisons, not an accuracy claim.
Applicability: when this calculator withholds a result
The implementation is deliberately narrower than the complete manual: slope 1:2.5 to 1:6; wave steepness 0.01 ≤ H/L0 ≤ 0.06; 0.5 ≤ ξ ≤ 4; toe depth/H ≥ 4; and nonnegative freeboard. These are conservative teaching screens for this simplified experiment, not a universal validity envelope or a guarantee of accuracy. The actual structure and sea state must also satisfy the stated assumptions.
Predicted Ru2% and q are withheld outside these screens. A negative freeboard introduces overflow, requiring different treatment. Very shallow foreshores, substantial infragravity energy, rough or permeable armour, berms, vertical walls, oblique attack and compound slopes need the appropriate additional formulations. Natural-beach run-up also requires a formulation developed for that setting; this structural calculator should not be relabelled as a beach predictor.
The dashed continued slope is a way to display a run-up statistic above a low crest. It does not model a sheet of water travelling through the air. No overtopping jets, individual-wave volumes, landward flooding, erosion, structural loads, safety thresholds or wave-driven currents are calculated.