A sea state contains
more than one wave height.
Real waves vary in height, period and direction. A characteristic height summarizes a sea state; it does not describe every wave within it. Begin by dividing an elevation record into complete waves, then ask what their statistics reveal—and what they conceal.
Wind sea, swell and mixed conditions
Wind sea receives energy from the local wind. Swell has propagated away from its generating weather system and often occupies a narrower range of frequencies and directions. Neither is perfectly monochromatic. A mixed sea can contain several systems at once, so a single characteristic period may hide important structure.
Two complementary descriptions
Wave-by-wave analysis identifies events between selected crossings and retains their individual heights and periods. Spectral analysis distributes variance over frequency and, when additional measurements are available, direction. An individual crossing-defined wave can be the local sum of several travelling components; it is not necessarily one identifiable wave system.
A · Define complete waves in the record
A 150 s synthetic A–E record, sampled every 0.05 s and demeaned using those samples. Shading identifies one complete wave; partial waves at the ends are excluded. Orange markers locate its crossing boundaries.
B · Rank the heights
Coral bars form the highest third, rounded up to a whole number of waves in this small sample. A rank is not the time order of a wave.
C · Keep height and period paired
A height is a vertical difference.
Between two successive crossings in the same direction, find the highest elevation and lowest elevation. Their difference is Hᵢ; the elapsed crossing-to-crossing time is Tᵢ. Several local crests may lie inside one crossing-defined wave. Counting every local maximum instead would answer a different question.
Which average answers the question?
The arithmetic mean H̄ describes a typical height averaged over all waves. The root-mean-square height Hrms gives more weight to large waves. H1/3 averages the highest third and H1/10 the highest tenth. Hmax is the largest observed height, so its value depends strongly on record length. None is automatically the height required for an engineering design.
Definitions and a short worked example
H̄ = ΣHᵢ/N; Hrms = √(ΣHᵢ²/N); T̄z = ΣTᵢ/N
For sorted heights 3.0, 2.4, 2.0, 1.6, 1.2 and 0.8 m, H̄ = 1.833 m, Hrms = 1.975 m and H1/3 = (3.0+2.4)/2 = 2.7 m. The maximum is 3.0 m. Averaging all six heights cannot produce H1/3.
For complete crossing intervals, T̄z equals (last crossing time − first crossing time)/N. Dividing the entire recording duration by the number of complete waves incorrectly includes the partial end intervals.
Elevation, height and probability are different quantities.
A linear sea made from many sufficiently independent components is often approximated by Gaussian surface elevation. Elevation may be positive or negative. Individual wave height is non-negative; for a narrow-band linear Gaussian sea, its distribution is approximately Rayleigh. A Gaussian elevation distribution does not by itself make every broad-band or breaking-wave height distribution Rayleigh.
Stationarity, ergodicity and covariance
Weak stationarity requires a constant mean and variance and covariance depending on time lag rather than absolute time. A slowly changing storm may be approximately stationary over a suitable short record, but the assumption must be checked. Ergodicity is the additional condition that long time averages can represent ensemble statistics; one short record does not prove it. Spatial homogeneity is a separate assumption and is not required merely to define a spectrum at one fixed station.
Cη(τ) = E[(η(t)−μ)(η(t+τ)−μ)]
For a stationary real process: Cη(τ) = ∫₀∞S(f) cos(2πfτ) df; Cη(0) = m₀
Covariance uses departures from the mean; uncentred correlation equals covariance only when the mean is zero. These statistical assumptions make a record informative about a sea state, but they do not turn its largest wave into a universal maximum.
Height–period dependence and shallow-water limitations
The scatterplot retains paired Hᵢ and Tᵢ values. In real records their joint density p(H,T) generally cannot be replaced by p(H)p(T) without testing independence. Marginal height or period distributions alone lose this pairing. Nonlinearity, wave breaking and finite depth can alter both distributions.
Near breaking, H1/3 and Hm0 can differ systematically as wave shape changes. Their ratio is not a universal depth correction. Report the measured or modelled definition explicitly rather than relabelling every height as Hs.
Probability within one idealized sea state
The spectral height Hm0 = 4√m₀ is defined from elevation variance m₀ and developed in Chapter 10. For the narrow-band Rayleigh approximation, set Hrms = Hm0/√2. The probability of a single wave exceeding h is Q(h) = exp[−2(h/Hm0)²]. The calculation below illustrates this model; it is not a fit to the five-component record above.
Single-wave exceedance versus the largest wave
For independent heights, P(Hmax > h) = 1 − [1−Q(h)]N. Setting NQ(h) = 1 gives h/Hm0 = √(ln N/2), a useful “one expected exceedance” level, not a guaranteed maximum or the exact expected maximum. Real grouping violates independence and changes maximum statistics.
At h = Hm0, Q = e−2 ≈ 13.5%. H1/3 is the mean of the largest third, not the threshold that exactly one third exceeds. Under Rayleigh assumptions that threshold is Hrms√ln3, and H1/10 is about 1.27 H1/3; these are model relationships rather than identities for every record.
Short-term exceedance concerns individual waves within a specified sea state. A 100-year return-level sea state concerns the long-term distribution of sea-state conditions. The two probabilities must not be substituted for each other.